dimmer-testata

Switch-on, switch-off and timed light control using Yokis digital modules

500w dimmer without neutral

dimmer-dimmer-temporizzato-500w-senza-neut

Flush-mounted

Model: MTV500E

Item number: 5454052

On DIN rail

Model: MTV500M

Item number: 5454062

WHAT MAKES YOKIS UNIQUE

UNIVERSAL: Compatible with the controls of all wiring systems.

Compatible with incandescent or dichroic light bulbs with ferromagnetic or electronic transformers.

Allows the use of several pushbuttons in parallel (two-way switch circuit or inverters).

COST-EFFECTIVE: The ability to dim brightness allows for significant cost saving.

COMFORTABLE: Soft Start and Soft Stop features.

THE ADVANTAGES OF THE 500W DIMMER WITHOUT NEUTRAL

Brightness can be adjusted within a 3% to 100% range for 5 to 500W loads by holding down the pushbutton.

Dual memory:

– The last brightness level set is stored and can be retrieved at the first press of the pushbutton.

– 100% brightness level is easily retrieved with 2 short presses of the pushbutton.

Built-in electronic protection in case of short circuit on the load, with automatic reset after the fault is eliminated.

Increases light bulb and pushbutton duration thanks to the "Soft Start" function.

Also works with pushbuttons equipped with light indicator (max 20) by adding a single BV40 accessory (item no. 5454071).

Download the EU declaration of conformity – item no. 5454052

Download the EU declaration of conformity – item no. 5454062

Technical features

Network voltage

230V ~ (+10% - 15%) - 50Hz

Power

min. 5VA max. 500VA (300VA in sealed boxes)

Maximum current

1.3A / 2.2A Sealed boxes: 1.3A / 300VA Other boxes: 2.2A / 500VA

Room temperature

-20°C + 40°C

Relative humidity

from 0 to 99%

Dimensions (mm)

see figure

dimension-mtr500
  • Variation principle through cut-off at phase start or phase end with automatic load type recognition.
  • The flush-mounted module MTV500E is 100% waterproof for outdoor installation.
  • Inrush current limitation through filament pre-heating
  • Built-in electronic protection in case of short circuit on the load, with automatic reset after the fault is eliminated.
  • Electronic overheating protection.
  • Double overload protection with power cut-off.
  • Digital coil with protection system in case pushbutton is pressed for a prolonged period of time.
  • Can be controlled by 12 or 48 VAC or DC with ADBT accessory.
  • Immune to mains disturbances up to 1.5 kV.

CVI50 (item n. 5454805): Allows the centralisation of modules from the 500 range

BV40 (item n. 5454071): Electronic coil. Allows the use of modules from the 500 range with pushbuttons equipped with light indicator

D600V (item n. 5454072): Diode for module centralisation with driver wire

CHR3W (item n. 5454070): Resistive load for energy-saving light bulbs and LEDS

ADBT (item n. 5454076): 12-48V AC or DC low-voltage adapter

SD541-0006_LR

Wiring connection of CHR3W with energy-saving light bulb or dimmable LED

Download datasheet

SD541-6051_LR

Radio control configuration for wired MTV500E dimmer

Download datasheet

sd541-0008

Centralised control of several dimmers

Download datasheet

sd541-0005

Increasing dimmable power

Download datasheet

sd541-0513

Dimmer controlled by low-voltage pushbuttons

Download datasheet

Relé_cablaggio-fase

Wiring with pushbutton common to live

Download datasheet

sd541-0002

Wiring with pushbutton common to neutral

Download datasheet

sd541-0003

Wiring in electric panel with pushbutton common to live

Download datasheet

sd541-0004

Wiring in electric panel with pushbutton common to neutral

Download datasheet